Buying a pump online is quick and convenient, but a product page can't see your equipment pad. Horsepower and "suits pools up to…" claims are a starting point, not a decision. The right pump is the one that matches your pool, your filter, your pipework and your space.
Work through these six checks before you order.
1. Work out the flow you need
Start with your pool volume. If you don't know it, use our Pool Volume Calculator. Then divide by how long you want to run the pump each day:
Flow (L/min) = pool volume (L) ÷ run time (minutes)
For example, a 40,000 L pool turned over in 6 hours (360 minutes) needs an average of about 110 L/min. That's a planning figure. Debris, bather load and climate all affect how long you actually need to run.
2. Check flow at real-world pressure, not maximum flow
The "maximum flow" on a spec sheet is measured with almost no resistance. Once a pump pushes water through pipes, valves, a filter and a chlorinator, it delivers less. Look at the pump's performance curve and read the flow at a realistic head. Around 8–12 m is typical for a residential pool.
3. Match the pump to your filter
This is the check most often missed. The pump's flow at your pool's operating pressure should not exceed your filter's maximum flow rating. An oversized pump on a small filter means high pressure, poorer filtration and extra wear.
| Poolrite filter | Max flow |
|---|---|
| S-5000 media | 200 L/min |
| S-6000 media | 280 L/min |
| S-8000 media | 450 L/min |
| CL50 cartridge | 325 L/min |
| CL100 cartridge | 370 L/min |
| CL150 / CL200 cartridge | 470 L/min |
A media filter also needs enough flow to backwash properly, so don't undersize the pump either.
4. Allow for other equipment
Chlorinators, heaters, heat pumps, suction cleaners, solar and spa jets all have their own flow needs. A chlorinator or heater may need a minimum flow, and spa jets or a water feature may need much more than daily filtration. A variable-speed pump can cover these with different speed settings.
5. Measure the fit
Before ordering, measure:
- Pipe size: most pools use 40 mm or 50 mm. Larger pumps such as the SQI-700 need 50 mm suction.
- Port centre heights: from the base to the centre of the inlet and outlet.
- Length and footprint: will it sit on the pad without forcing the pipes?
- Service clearance: room to lift the lid, remove the basket and keep the motor ventilated.
If you're replacing a Poolrite SQI or SQ Junior, the SQ Pro variable-speed pump is designed as a drop-in replacement without re-plumbing.
6. Check the model, the electrics and support
- Confirm the exact model code and that it's an Australian-market model with Australian compliance markings.
- Check what's included: unions, O-rings and the controller.
- Check who handles warranty and whether spare parts (lids, baskets, seals, impellers) are available locally. Poolrite stocks genuine spares for its current range.
- A pump needs a weatherproof outlet with RCD protection. New circuits or outlets must be installed by a licensed electrician.
Single-speed or variable-speed?
A single-speed pump runs every task at one speed. A variable-speed pump lets you filter slowly and quietly most of the time, then speed up for vacuuming or backwashing. It uses far less energy. See Single-Speed vs Variable-Speed Pool Pumps.
Don't use a bigger pump to fix a problem
If your current system has weak flow, high pressure or air in the pump basket, fix the cause first. A stronger pump won't clear a blocked filter, a leaking suction line or a closed valve. It just pushes harder against it.
FAQs
Can I just buy the same horsepower as my old pump?
It's a reasonable starting point if the old pump worked well, but check flow, filter rating and fit too. Two 1.5 hp pumps can perform quite differently.
Is a bigger pump better because it can run fewer hours?
Not usually. It can exceed your filter's rating and uses more power. A correctly sized or variable-speed pump is more efficient.
Will a variable-speed pump work with my older filter and chlorinator?
Usually, yes. Set the lowest speed high enough for the chlorinator's flow switch and for good skimming.
Not sure?
Send your local Poolrite dealer photos of your equipment pad and model labels, plus your pool volume. Or browse the Poolrite pump range.
Need a hand?
Our team can help with Poolrite pumps, filters, skimmers and parts. Find a Poolrite dealer near you, or contact us on (07) 3155 6531, Monday to Friday.


