Run your pump too little and the water turns cloudy or green. Run it too much and you pay for power you don't need. The right run time depends on your pool's volume, your pump's flow, the season and how much the pool is used.
The quick answer
As a starting point for most Australian backyard pools:
- Summer: about 8 hours a day
- Winter: about 4–6 hours a day
Then fine-tune using the turnover method below and how your water looks.
Work out your turnover
A "turnover" means the pump has moved a volume of water equal to the whole pool through the filter. Most pools need at least one turnover a day, and more in hot weather or with heavy use.
Hours for one turnover = pool volume (L) ÷ pump flow (L/min) ÷ 60
For example, a 50,000 L pool with a pump delivering about 200 L/min through the filter needs roughly 50,000 ÷ 200 ÷ 60 = 4.2 hours for one turnover. Two turnovers in peak summer would be about 8–9 hours.
Don't know your volume? Use our Pool Volume Calculator. Remember your pump's real flow through the filter is lower than its maximum rated flow.
When to run longer
- Hot weather. Warm water and strong sun use up chlorine and help algae grow.
- Heavy use. Parties, school holidays and lots of swimmers add sunscreen and body oils.
- After storms or leaf drop. Extra debris and dilution need more filtering and sanitising.
- Your chlorinator can't keep up. A salt or mineral chlorinator only makes chlorine while the pump runs. If chlorine tests low, more run time may be the answer.
- Cloudy water. Run longer while you correct the chemistry.
When you can run less
In cool weather with little use, water needs less filtering and sanitising. But don't switch off altogether. A pool left without circulation for long periods can turn green, and stagnant water is harder to recover than to maintain.
Variable-speed pumps: run longer, slower
With a variable-speed pump like the Poolrite SQ Pro, the rules change. Running at low speed for more hours moves the same water for a fraction of the power. A typical set-up:
- Low speed for most of the day for filtration and skimming
- A short high-speed period for skimming heavy debris, a suction cleaner or a heater
- High speed for priming and backwashing
Make sure the low speed still keeps the skimmer drawing surface debris, and gives your chlorinator and any heater enough flow to switch on. See Single-Speed vs Variable-Speed Pool Pumps. Thinking of upgrading? Browse the Poolrite pool pump range or look at the SQ Pro 1.0 hp.
When to run it
- Daytime is usually best for a chlorinated pool, because the sun breaks down chlorine and the chlorinator can replace it as it's used.
- Rooftop solar: running in the middle of the day uses your own solar power.
- Off-peak tariff: if you're on a time-of-use plan without solar, cheaper hours may suit, but check your chlorine levels stay up.
- Split it up: two shorter runs (morning and afternoon) can work well in summer.
Let the water tell you
The right run time is the shortest one that keeps your water clear and your chlorine in range. Test your water regularly, about twice a week in summer and weekly in winter. If it starts to dull or chlorine drops, add an hour. If it stays sparkling, try trimming back.
FAQs
Should I run my pool pump 24 hours a day?
Not usually. It wastes power and wears the pump. A correctly sized pump running the right hours does the job.
Is it better to run the pump during the day or at night?
For most chlorinated pools, during the day, when chlorine is being used up by the sun and swimmers.
Can I turn my pump off in winter?
Reduce the hours, but keep it running daily. Water that doesn't circulate turns green quickly once it warms up.
Will a bigger pump let me run fewer hours?
It can, but it uses more power, may exceed your filter's rating and filters less effectively. A variable-speed pump running longer at low speed is usually cheaper.
Need a hand?
Our team can help with Poolrite pumps, filters, skimmers and parts. Find a Poolrite dealer near you, or contact us on (07) 3155 6531, Monday to Friday.


